玩一玩波音777冷艙啟動

支 持 本 站: 捐贈伺服器等運維費用,需要您的支持!

上次網友問起冷艙啟動的問題
想起來以前測試VMAX-777-Pro Boeing 777 Worldliner Professional時有些拷屏,
那麼就結合插件中提供的777 Pilot's Handbook操作手冊做一個小小的攻略。
這個手冊是波音公司授權給軟體開發商的,其權威性不容置疑。

首先看一下這個777的插件的主菜單,加燃油的操作在這裡完成。

下面按照手冊里的Normal Prececure來進行啟動操作,
具體請看手冊,自己拷屏的步驟並不很完整。

Preflight Procedure - First Officer
頂板檢查,從左至右,從上往下
Overhead maintenance panel ...................Check
Verify:
• all guards closed
• flight control VALVE CLOSED lights extinguished.


支 持 本 站: 捐贈伺服器等運維費用,需要您的支持!


CARGO TEMPERATURE selectors - As required

ADIRU switch ................................ ON
Verify ON BAT and OFF lights extinguished.
Note: A complete ADIRU alignment is recommended if the total
time in the navigation mode is expected to exceed 24 hours.
THRUST ASYMMETRY COMPENSATION
switch .......................................AUTO
Verify OFF light extinguished.
PRIMARY FLIGHT COMPUTERS
DISCONNECT switch ...........................AUTO (guarded position)
Verify DISC light extinguished.

ELECTRICAL panel............................. Set
BATTERY switch - ON
Verify OFF light extinguished.
IN-FLIGHT ENTERTAINMENT SYSTEM/PASSENGER
SEATS POWER and CABIN/UTILITY POWER switches - ON
Verify OFF lights extinguished.
APU GENERATOR switch - ON
Verify OFF light extinguished.
APU selector - START
Verify FAULT light extinguished.
BUS TIE switches - AUTO
Verify ISLN lights extinguished.
GENERATOR CONTROL switches - ON
OFF and DRIVE lights remain illuminated until respective engine is
started.
BACKUP GENERATOR switches - ON
OFF lights remain illuminated until respective engine is started.

HYDRAULIC panel .............................Set
LEFT and RIGHT PRIMARY pump switches - ON
Left and right primary pump ON light remains in off position until
respective engine is started.
C1 and C2 PRIMARY pump switches - OFF
Verify FAULT lights illuminated.
DEMAND pump selectors - OFF
Verify FAULT lights illuminated.

PASSENGER SIGNS panel ...................... Set
NO SMOKING selector - AUTO or ON
SEAT BELTS selector - ON
Lighting panel ............................. Set
DOME light control - Adjust
STORM light switch - As desired
MASTER BRIGHTNESS control - Adjust
Glareshield light controls - Mid position
LANDING light switches - OFF

ENGINE panel.............................Set
EEC MODE switches - NORM
START/IGNITION selectors - NORM
AUTOSTART switch - ON
Verify OFF light extinguished.

FUEL JETTISON panel ..........................Set
FUEL JETTISON NOZZLE switches - Off
Verify VALVE lights extinguished.
FUEL TO REMAIN selector - IN
FUEL JETTISON ARM switch - Off
Verify FAULT light extinguished.
FUEL panel ..................................Set
CROSSFEED switches - OFF
Verify VALVE lights extinguished.
FUEL PUMP switches - OFF
Left and right pump PRESS lights are illuminated.
Left forward pump PRESS light is extinguished if the APU is running.
Both center pump PRESS lights are extinguished.

ANTI-ICE panel...............................Set
WING anti-ice selector - AUTO
ENGINE anti-ice selectors - AUTO
Lighting panel ..............................Set
BEACON light switch - OFF
NAVIGATION light switch - ON
LOGO light switch - ON during nighttime operation
WING light switch - As required
INDICATOR LIGHTS switch - As desired
RUNWAY TURNOFF, TAXI, and STROBE light switches - OFF

AIR CONDITIONING panel ............................ Set
EQUIPMENT COOLING switch - AUTO
Verify OVRD light extinguished.
RECIRCULATION FANS switches - ON
FLIGHT DECK TEMPERATURE control - AUTO (mid position)
CABIN TEMPERATURE control - Mid position
PACK switches - AUTO
Verify OFF lights extinguished.
TRIM AIR switches - ON
Verify FAULT lights extinguished.
BLEED AIR panel ................... Set
Bleed ISOLATION switches - ON
Verify CLOSED lights extinguished.
ENGINE bleed switches - ON
Verify OFF lights illuminated.
APU bleed switch - AUTO
Verify OFF light extinguished.
PRESSURIZATION panel ...................... Set
OUTFLOW VALVE switches - AUTO
Verify MAN lights extinguished.
LANDING ALTITUDE selector - IN

這時候油應該加完了,看一下數值對不對

接下來是MCP和EFIS
Right FLIGHT DIRECTOR switch ................ ON
Display select panel ........................Set
LWR CTR display switch - Push
Right EFIS control panel .....................Set
MINIMUMS reference selector - As desired
MINIMUMS selector - Minimum shall be blanked
FLIGHT PATH VECTOR switch - Flight path vector shall be
blanked
METERS switch - Meters indication shall be blanked except when
meters information is required.
BAROMETRIC reference and BAROMETRIC selectors - Set
Set the local altimeter setting on the PFD.
VOR/ADF switches - As desired
ND mode selector - MAP
Use ND expanded map mode for all phases of flight.
ND CENTER switch - Select expanded display
ND range selector -Select:
ND TRAFFIC switch - Select ON
Map switches - As desired

加熱器和亮度這些就不具體貼出來了

Right PFD ..............................Check
Flight mode annunciations - Verify:
• autothrottle mode is blank
• roll mode is TO/GA
• pitch mode is TO/GA
• AFDS status is FLT DIR.

Right ND ...............................Check
Verify expanded map mode displayed.
Right INBOARD DISPLAY selector ........... MFD
FMC Selector ............................ AUTO
Landing gear panel ....................... Set
GROUND PROXIMITY light - Extinguished
Ground proximity FLAP OVERRIDE switch - Off
Ground proximity GEAR OVERRIDE switch - Off
Ground proximity TERRAIN OVERRIDE switch - Off
Landing gear lever - DN
ALTERNATE GEAR switch - NORM (guarded position)
AUTOBRAKE selector - RTO

EICAS display ............................ Check
Indications - Normal. Verify:
• primary engine indications display existing conditions
• no exceedance values are displayed.

MFD ...................................... Check
Secondary ENGINE display switch - Push
Secondary ENGINE display - Verify:
• secondary engine indications display existing conditions
• no exceedance values are displayed.

STATUS display switch - Push
STATUS display - Verify:
• hydraulic quantities do not display RF
• oxygen pressure is sufficient for flight.
If any status message is displayed, refer to the Minimum Equipment
List and Dispatch Deviation Guide to determine if dispatch relief is
available.

FLAP position indication and FLAP lever .... Agree
Flap position indication is blank when flaps are up.
ALTERNATE FLAPS panel ..................... Set
ALTERNATE FLAPS ARM switch - OFF
ALTERNATE FLAPS selector - OFF

Engine fire panel ......................... Set
ENG BTL 1 DISCH and ENG BTL 2 DISCH lights - Extinguished
Engine fire switches - In
Verify LEFT and RIGHT fire warning lights extinguished.

無線電通訊設備也比較簡單,也不詳細貼出來了

接下來是FMC的CDU設置,
Right CDU .................................Set
INIT REF key - Push
INDEX line select key - Push
IDENT line select key - Push
IDENT page - Check
Verify active date current.
POS INIT line select key - Push
Verify time correct.
Inertial position - Enter
Enter inertial position using the most accurate latitude and
longitude.

ROUTE line select key - Push
Enter:
• flight number
• route.
ACTIVATE line select key - Push
EXEC key - Push
DEP ARR key - Push
Select runway and SID.
ROUTE line select key - Push
Verify SID and route are correct.
EXEC key - Push

NAV RAD key - Push

Set/verify navigation radio tuning.
PERF INIT line select key - Push
Enter:
• fuel reserves
• cruise altitude
• cost index.
Check and/or enter:
• minimum fuel temperature value (enter freeze point temperature for
the type of fuel being used if the correct value is not displayed)
• cruise CG
• step size values.
TAKEOFF line select key - Push
Enter takeoff flap setting.
Check and/or enter:
• acceleration height
• engine-out acceleration height
• thrust reduction point
• runway wind component
• runway slope
• runway position value

然後就是Preflight Procedure - Captain,進行的內容基本差不多,
完成之後就可以等待進入Before Start Procedure,
CDU..................................... Set C
INIT REF key - Push
Verify fuel quantities agree:
• upload fuel quantity
• EICAS
• CDU.
Enter: zero fuel weight
THRUST LIM line select key - Push
Select takeoff thrust:
• full thrust
• assumed temperature derate.
TAKEOFF line select key - Push
Enter CG.
Select or enter takeoff speeds.

MCP............................... Set C
IAS/MACH selector - Rotate
Set V2 speed in the IAS/MACH window.
LNAV switch - As required
VNAV switch - Push

獲得pushback許可以後,就能夠啟動液壓和燃油,
HYDRAULIC panel.................Set F/O
Note: Pressurize right system first to prevent fluid transfer between
systems.
Right DEMAND pump selector - AUTO
Verify FAULT light extinguished.
C1 and C2 PRIMARY pump switches - ON
Verify FAULT lights extinguished.
Note:With only a single ground power source available,
including the APU, the C2 PRIMARY pump will not run
if the C1 pump is selected ON. The C2 primary pump
FAULT light remains illuminated until an engine
generator is operating. The HYD PRESS PRI C2
message is inhibited.
Left, C1, and C2 DEMAND pump selectors - AUTO
Verify FAULT lights extinguished.
FUEL panel .............................Set F/O
LEFT and RIGHT FUEL PUMP switches - ON
Verify PRESS lights extinguished.
If center tank contains fuel:
CENTER FUEL PUMP switches - ON
Verify PRESS lights extinguished.
Note: One or both PRESS lights may not be extinguished due to
load shedding. Indications will be normal after engine
start.
BEACON light switch .......................ON F/O

推出後就可以啟動發動機,執行Engine Start Procedure了。
First Officer
Position ____ START/ IGNITION
selector to START.

Captain
Position ____ FUEL CONTROL
switch to run.



支 持 本 站: 捐贈伺服器等運維費用,需要您的支持!